PV Powered PVP260kW Technical Information Page 47
- Page / 129
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
33
PVP250kW & PVP260kW Inverter
Installation & Operation Manual
2. Position the inverter to the preferred location.
Alternate methods of lifting and positioning the inverter may be used. Proper
methods may include the use of a crane with a strap rated for the weight of the
inverter; however, care MUST be taken to protect the inverter from compressive
stresses or forces which may dent or deform the cabinet or cause damage to the
inverter. Use of lifting beams, spreader bars, or similar equipment rated for the
weight of the inverter can be employed for this purpose. Damage caused by
improper handling may void the warranty.
Safe operating, handling, and installation practices are the responsibility of the
installer.
3. Secure the inverter to the concrete base by setting the anchoring hardware through
each of the six holes in the external mounting ange as shown in sheet two of
Appen-
dix C - Mechanical Drawings
.
The anged inverter base allows the unit to be anchored after positioning.
4.4 Conduit Entry
AC and DC cables can be brought into the inverter through the side or bottom gland
plates as shown in
Appendix C - Mechanical Drawings
.
!
WARNING
All penetrations in the inverter cabinet must be through the six gland plates
which are provided for the sole purpose of providing a safe and convenient
way to bring wiring in to and out of the inverter. Penetrating the inverter
housing in any other location besides the gland plates voids the warranty.
!
AVERTISSEMENT
Tout travail à l’intérieur de la structure de l’onduleur doit être effectué en
démontant les plaques libres conçues uniquement pour fournir des ouvertures
permettant de travailler facilement et en toute sécurité sur le câblage de
l’appareil. Tout travail effectué à partir d’autres ouvertures entrainerait une
annulation de la garantie.
Using Gland Plates for Cable Entry and Exit
All power cabling and communications wiring must enter and exit via the inverter
cabinet’s gland plates. There are gland plates on the AC and DC sides of the inverter for
bottom and side entry. In addition, there is a gland plate on the upper right side for data
monitoring wiring. Each gland plate location is selected to ensure safe installation, proper
airow and prevention of dust, debris, moisture, insect and animal incursion. Do not
penetrate the cabinet at any other location. All gland plates need to be installed for proper
operation of the inverter.
To use a gland plate:
1. Select the size(s) and location(s) of the hole(s) that need to be punched.
2. Remove the gland plate while taking care not to damage the weatherproof gasket
material on the back side of the plate.
- 97-600100-28-C 1
- Acronyms and Abbreviations 7
- Table of Contents 9
- List of Tables 11
- List of Figures 12
- 1. Introduction 15
- 1.2 Product Characteristics 16
- 1.3 Product Features 16
- Card Cage Assembly 18
- Controller PCB 18
- Power Distribution PCB 18
- Communications PCB 18
- Figure 1-4 AC Sub Panel 19
- AC Sense & DC Power 20
- Supply Fuses 20
- Power Supply Fuses (optional) 20
- Soft Start Fuses 20
- DC Sub Panel 21
- AVERTISSEMENT 22
- 2. Safety 25
- 2.3 Personal Safety 29
- 2.4 Wiring Requirement 29
- PRUDENCE 31
- Model 480VAC 600VAC 32
- 3. Planning 35
- 3.4 Conduits and Conductors 36
- CAUTION 38
- WARNING 38
- 3.7 Grid Interconnection 39
- 3.8 Monitoring 39
- 3.10 PV Array Input 40
- 4. Installation 41
- Figure 4-2 Screen Check 43
- Figure 4-7 Screen Inspection 44
- Figure 4-9 Fan Inspection 45
- 4.3 Setting and Anchoring 46
- 4.4 Conduit Entry 47
- 4.5 Electrical Connections 48
- 2 inch straight 49
- Lower cabinet 49
- PVP250kW 400A 350A 52
- PVP260kW 400A N/A 52
- PVP260kW-LV 400A N/A 52
- 480VAC 422VAC – 528VAC 52
- 600VAC 528VAC - 660VAC 52
- 4.7 DC Wiring 55
- 1 2 3 4 5 6 7 8 58
- 4.4 Conduit Entry 59
- Chapter 5, Modbus 60
- Network Installation 60
- C. Connect the Modbus cable 64
- Table 5-4 Biasing Enabled 67
- Modbus Register Maps 70
- 6. Operation 77
- Initialize 79
- Disabled 79
- 6.5 Shutdown Procedure 84
- Figure 7-1 Air Intake Hood 87
- 7.5 Faults and Warnings 88
- 7.6 Troubleshooting Faults 90
- Start Up Procedure 92
- Status LED Lights 93
- Figure 7-7 Comm X PCB Lights 94
- DNS Failure Long-Short-Short 95
- Torque Values, and Wire Sizes 96
- Appendix A - Specifications 97
- Appendix B - Wiring Diagram 99
- 3 PHASE AC OUT 100
- INSTALLER 100
- INSTALLER LANDINGS 100
- LANDINGS 100
- APPENDIX C 102
- 10-810006-06 103
- WEIV MOTTOB 104
- Values, and Wire Sizes 108
- DC Subcombiner Inputs 112
- Requirements Checklist 114
- Appendix F - Efficiency Curves 116
- CEC Efficiency = 96.5% 117
- CEC Efficiency = 97.0% 118
- Limited Warranty 124
Related products and manuals for Power adapters & inverters PV Powered PVP260kW
(34 pages)Roland BR-1600CD podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt rejestrujący Roland BR-1600CD.
Dostarczamy 2 pdf podręczników Roland BR-1600CD do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comments to this Manuals